dmesg一覧へ

DELL PowerEdge 2950III + CentOS 4.4(x86)のdmesg

Linux version 2.6.9-42.ELsmp (buildcentos@build-i386) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 SMP Sat Aug 12 09:39:11 CDT 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 0000000000100000 - 00000000cfb50000 (usable)
 BIOS-e820: 00000000cfb50000 - 00000000cfb66000 (reserved)
 BIOS-e820: 00000000cfb66000 - 00000000cfb85c00 (ACPI data)
 BIOS-e820: 00000000cfb85c00 - 00000000d0000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fe000000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000230000000 (usable)
8064MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
NX (Execute Disable) protection: active
On node 0 totalpages: 2293760
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:16
  HighMem zone: 2064384 pages, LIFO batch:16
DMI 2.4 present.
ServerWorks chipset detected. Disabling timer routing over 8254.
Using APIC driver default
ACPI: RSDP (v002 DELL                                  ) @ 0x000f1ce0
ACPI: XSDT (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x000f1d7c
ACPI: FADT (v003 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x000f1ebc
ACPI: MADT (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x000f1fb0
ACPI: SPCR (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x000f2067
ACPI: HPET (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x000f20b7
ACPI: MCFG (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x000f20ef
ACPI: WD__ (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x000f212b
ACPI: SLIC (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x000f225f
ACPI: ERST (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0xcfb6d3e0
ACPI: HEST (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0xcfb6d5f0
ACPI: BERT (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0xcfb6d260
ACPI: EINJ (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0xcfb6d290
ACPI: TCPA (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x000f23e1
ACPI: SSDT (v001 DELL   PE_SC3   0x00000011 INTL 0x20050624) @ 0xcfb6a9a6
ACPI: SSDT (v001 DELL   PE_SC3   0x00000011 INTL 0x20050624) @ 0xcfb6afef
ACPI: SSDT (v001 DELL   PE_SC3   0x00000011 INTL 0x20050624) @ 0xcfb6b47c
ACPI: SSDT (v001 DELL   PE_SC3   0x00000011 INTL 0x20050624) @ 0xcfb6b909
ACPI: SSDT (v001 DELL   PE_SC3   0x00000011 INTL 0x20050624) @ 0xcfb6bd96
ACPI: SSDT (v001 DELL   PE_SC3   0x00000011 INTL 0x20050624) @ 0xcfb6c223
ACPI: SSDT (v001 DELL   PE_SC3   0x00000011 INTL 0x20050624) @ 0xcfb6c6b0
ACPI: SSDT (v001 DELL   PE_SC3   0x00000011 INTL 0x20050624) @ 0xcfb6cb3d
ACPI: SSDT (v001 DELL   PE_SC3   0x00000010 INTL 0x20050624) @ 0xcfb6cfca
ACPI: DSDT (v001 DELL   PE_SC3   0x00000001 INTL 0x20050624) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:7 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)
Processor #4 6:7 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
Processor #1 6:7 APIC version 20
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x05] enabled)
Processor #5 6:7 APIC version 20
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x02] enabled)
Processor #2 6:7 APIC version 20
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
Processor #6 6:7 APIC version 20
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x03] enabled)
Processor #3 6:7 APIC version 20
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
Processor #7 6:7 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
Enabling APIC mode:  Flat.  Using 0 I/O APICs
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at d1000000 (gap: d0000000:10000000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet console=ttyS1,57600 console=tty
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
CPU 0 irqstacks, hard=c03ee000 soft=c03ce000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 8304796k/9175040k available (1876k kernel code, 77964k reserved, 759k data, 184k init, 7466304k highmem)
Using HPET for base-timer
Using HPET for gettimeofday
Detected 2327.644 MHz processor.
Using hpet for high-res timesource
Calibrating delay using timer specific routine.. 4657.80 BogoMIPS (lpj=2328903)
Security Scaffold v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 20100000 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU0: Physical Processor ID: 0
CPU0: Processor Core ID: 0
CPU0: Initial APIC ID: 0
CPU: After all inits, caps:        bfebfbff 20100000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
per-CPU timeslice cutoff: 1738.07 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c03ef000 soft=c03cf000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4655.08 BogoMIPS (lpj=2327544)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 20100000 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU1: Physical Processor ID: 0
CPU1: Processor Core ID: 1
CPU1: Initial APIC ID: 1
CPU: After all inits, caps:        bfebfbff 20100000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
Booting processor 2/2 eip 3000
CPU 2 irqstacks, hard=c03f0000 soft=c03d0000
Initializing CPU#2
Calibrating delay using timer specific routine.. 4655.08 BogoMIPS (lpj=2327544)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 20100000 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU2: Physical Processor ID: 0
CPU2: Processor Core ID: 2
CPU2: Initial APIC ID: 2
CPU: After all inits, caps:        bfebfbff 20100000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
Booting processor 3/3 eip 3000
CPU 3 irqstacks, hard=c03f1000 soft=c03d1000
Initializing CPU#3
Calibrating delay using timer specific routine.. 4655.03 BogoMIPS (lpj=2327518)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 20100000 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU3: Physical Processor ID: 0
CPU3: Processor Core ID: 3
CPU3: Initial APIC ID: 3
CPU: After all inits, caps:        bfebfbff 20100000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
Booting processor 4/4 eip 3000
CPU 4 irqstacks, hard=c03f2000 soft=c03d2000
Initializing CPU#4
Calibrating delay using timer specific routine.. 4655.05 BogoMIPS (lpj=2327525)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 20100000 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU4: Physical Processor ID: 1
CPU4: Processor Core ID: 4
CPU4: Initial APIC ID: 4
CPU: After all inits, caps:        bfebfbff 20100000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#4.
CPU4: Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
Booting processor 5/5 eip 3000
CPU 5 irqstacks, hard=c03f3000 soft=c03d3000
Initializing CPU#5
Calibrating delay using timer specific routine.. 4655.11 BogoMIPS (lpj=2327557)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 20100000 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU5: Physical Processor ID: 1
CPU5: Processor Core ID: 5
CPU5: Initial APIC ID: 5
CPU: After all inits, caps:        bfebfbff 20100000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#5.
CPU5: Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
Booting processor 6/6 eip 3000
CPU 6 irqstacks, hard=c03f4000 soft=c03d4000
Initializing CPU#6
Calibrating delay using timer specific routine.. 4655.08 BogoMIPS (lpj=2327541)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 20100000 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU6: Physical Processor ID: 1
CPU6: Processor Core ID: 6
CPU6: Initial APIC ID: 6
CPU: After all inits, caps:        bfebfbff 20100000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#6.
CPU6: Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
Booting processor 7/7 eip 3000
CPU 7 irqstacks, hard=c03f5000 soft=c03d5000
Initializing CPU#7
Calibrating delay using timer specific routine.. 4655.05 BogoMIPS (lpj=2327529)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 20100000 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU7: Physical Processor ID: 1
CPU7: Processor Core ID: 7
CPU7: Initial APIC ID: 7
CPU: After all inits, caps:        bfebfbff 20100000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#7.
CPU7: Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
Total of 8 processors activated (37243.32 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 8 CPUs: passed.
Brought up 8 CPUs
zapping low mappings.
checking if image is initramfs... it is
Freeing initrd memory: 458k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb05e, last bus=14
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.PE2P._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 20 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 20 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:05:01.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:07:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:0e:0d.0[A] -> GSI 19 (level, low) -> IRQ 193
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1201119616.633:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 10EA8AC2C8019830
- User ID: CentOS (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU1] (supports C1)
ACPI: Processor [CPU2] (supports C1)
ACPI: Processor [CPU3] (supports C1)
ACPI: Processor [CPU4] (supports C1)
ACPI: Processor [CPU5] (supports C1)
ACPI: Processor [CPU6] (supports C1)
ACPI: Processor [CPU7] (supports C1)
ACPI: Processor [CPU8] (supports C1)
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ESB2: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 169
ESB2: chipset revision 9
ESB2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: HL-DT-STDVD-ROM GDR-T10N, ATAPI CD/DVD-ROM drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: ATAPI 24X DVD-ROM drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP route cache hash table entries: 524288 (order: 9, 2097152 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 262144 (order: 9, 3145728 bytes)
TCP: Hash tables configured (established 262144 bind 262144)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S4 S5)
ACPI wakeup devices: 
PCI0 
Freeing unused kernel memory: 184k freed
SCSI subsystem initialized
megasas: 00.00.03.16 Mon Oct. 15 08:15:20 PDT 2007
megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 1:slot 0:func 0
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
megasas: FW now in Ready state
megasas: max_sectors : 0x280, cmd_per_lun : 0x80
scsi0 : LSI Logic SAS based MegaRAID driver
  Vendor: DP        Model: BACKPLANE         Rev: 1.05
  Type:   Enclosure                          ANSI SCSI revision: 05
  Vendor: DELL      Model: PERC 6/i          Rev: 1.11
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 570949632 512-byte hdwr sectors (292326 MB)
SCSI device sda: drive cache: write back, no read (daft)
SCSI device sda: 570949632 512-byte hdwr sectors (292326 MB)
SCSI device sda: drive cache: write back, no read (daft)
 sda: sda1 sda2
Attached scsi disk sda at scsi0, channel 2, id 0, lun 0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux:  Disabled at runtime.
SELinux:  Unregistering netfilter hooks
inserting floppy driver for 2.6.9-42.ELsmp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.38 (February 10, 2006)
ACPI: PCI interrupt 0000:07:00.0[A] -> GSI 16 (level, low) -> IRQ 169
divert: allocating divert_blk for eth0
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001c23d8cfcb
ACPI: PCI interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 169
divert: allocating divert_blk for eth1
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001c23d8cfc9
_OSC FW not grant req. control
pciehp: Both _OSC and OSHP methods do not exist
_OSC FW not grant req. control
pciehp: Both _OSC and OSHP methods do not exist
hw_random hardware driver 1.0.0 loaded
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 177
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 177, pci mem f8878000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 177
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 177, io base 0000cce0
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 20 (level, low) -> IRQ 185
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 185, io base 0000ccc0
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 177
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 177, io base 0000cca0
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 20 (level, low) -> IRQ 185
uhci_hcd 0000:00:1d.3: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 185, io base 0000cc80
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 1-1: new high speed USB device using address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 2 ports detected
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0344160(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
usb 1-5: new high speed USB device using address 4
hub 1-5:1.0: USB hub found
hub 1-5:1.0: 4 ports detected
usb 1-1.1: new full speed USB device using address 5
ehci_hcd 0000:00:1d.7: qh f6543280 (#0) state 1
input: USB HID v1.10 Keyboard [Dell DRAC5] on usb-0000:00:1d.7-1.1
input: USB HID v1.10 Mouse [Dell DRAC5] on usb-0000:00:1d.7-1.1
usb 1-1.2: new high speed USB device using address 6
usb 3-1: new low speed USB device using address 2
Initializing USB Mass Storage driver...
scsi1 : SCSI emulation for USB Mass Storage devices
  Vendor: Dell      Model: Virtual  CDROM    Rev: 123 
  Type:   CD-ROM                             ANSI SCSI revision: 02
USB Mass Storage device found at 6
scsi2 : SCSI emulation for USB Mass Storage devices
  Vendor: Dell      Model: Virtual  Floppy   Rev: 123 
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sdb at scsi2, channel 0, id 0, lun 0
USB Mass Storage device found at 6
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
sr0: scsi-1 drive
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
input: USB HID v1.10 Keyboard [Avocent Dell 03R874] on usb-0000:00:1d.1-1
input: USB HID v1.10 Mouse [Avocent Dell 03R874] on usb-0000:00:1d.1-1
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
ACPI: Power Button (FF) [PWRF]
EXT3 FS on sda1, internal journal
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
cdrom: open failed.
Adding 8385920k swap on /dev/sda2.  Priority:-1 extents:1
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: No new microdata for cpu 1
microcode: No new microdata for cpu 2
microcode: No new microdata for cpu 3
microcode: No new microdata for cpu 6
microcode: No new microdata for cpu 4
microcode: No new microdata for cpu 7
microcode: No new microdata for cpu 5
microcode: No new microdata for cpu 0
IA-32 Microcode Update Driver v1.14 unregistered
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
MSI INIT SUCCESS
bnx2: eth0: using MSI
bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex
ip_tables: (C) 2000-2002 Netfilter core team
bnx2: eth1: using MSI
bnx2: eth1 NIC Link is Up, 1000 Mbps full duplex
i2c /dev entries driver
lp: driver loaded but no devices found
eth0: no IPv6 routers present
ipmi message handler version 33.13
IPMI System Interface driver version 33.13, KCS version 33.13, SMIC version 33.13, BT version 33.13
ipmi_si: Found SMBIOS-specified state machine at I/O address 0xca8, slave address 0x20
eth1: no IPv6 routers present
 IPMI kcs interface initialized
ipmi device interface version 33.13
Fusion MPT base driver 3.02.62.01rh
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT misc device (ioctl) driver 3.02.62.01rh
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor=10,220)
Attached scsi generic sg0 at scsi0, channel 0, id 32, lun 0,  type 13
Attached scsi generic sg1 at scsi0, channel 2, id 0, lun 0,  type 0
Attached scsi generic sg2 at scsi1, channel 0, id 0, lun 0,  type 5
Attached scsi generic sg3 at scsi2, channel 0, id 0, lun 0,  type 0
Device sr0 not ready.