uboot

Fork

arm: dts: mt7622: remove default pinctrl of uart0

Currently u-boot running on mt7622 will print an warning log at beginning:
> serial_mtk serial@11002000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19

It turns out that the pinctrl uclass can't work properly in board_f stage.

Since the uart0 is the default UART device used by bootrom, and will be
initialized in both bootrom and tf-a bl2. It's ok not to setup pinctrl for
uart0 in u-boot.

This patch removes the default pinctrl of uart0 to suppress the unwanted
warning.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>

arm: dts: k3-am64-ddr fix typo causing DDR4 register corruption

The entry for DDRSS_PI_321_DATA was accidentally repeated leading to the
last few PI registers being incorrectly programmed.

Fix this.

Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

board: qualcomm: Add support for QCS404 EVB

Add support for Qualcomm QCS404 SoC based evaluation board.

Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot

U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>

clocks: qcom: Add clock driver for QCS404 SoC

Currently this clock driver initializes clocks for UART and eMMC. Along
with this import "qcom,gcc-qcs404.h" header from Linux mainline to
support DT bindings.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>

pinctrl: qcom: Add pinctrl driver for QCS404 SoC

Currently this pinctrl driver only supports BLSP UART2 specific pin
configuration.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

mmc: msm_sdhci: Add SDCC version 5.0.0 support

For SDCC version 5.0.0, MCI registers are removed from SDCC interface
and some registers are moved to HC. So add support to use the new
compatible string "qcom,sdhci-msm-v5". Based on this new msm variant,
pick the relevant variant data and use it to detect MCI presence thereby
configuring register read/write to msm specific registers.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

board: qualcomm: Add support for dragonboard845c

Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.

Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive

U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

uart: sdm845: Fix debug UART pinmux

Configure debug UART pins as function: "qup9" rather than being regular
gpios. It fixes a hang seen during pinmux setting.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

clocks: sdm845: Import qcom,gcc-sdm845.h

Rather than using magic numbers as clock ids for peripherals import
qcom,gcc-sdm845.h from Linux to be used standard macros for clock ids.
So start using corresponding clk-id macro for debug UART.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

arm64: dts: sdm845: Remove redundant u-boot DT properties

According to u-boot DT recomendation, u-boot specific DT properties belong
to *-uboot.dtsi. Also for starqltechn board (which is the only current
consumer of sdm845.dtsi), the properties are already included in
starqltechn-uboot.dtsi, so remove corresponding redundant properties.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

board: starqltechn: Align DT node overrides with sdm845.dtsi

Currently there is a mismatch among DT node overrides in starqltechn
board DTS file and the actual DT nodes in the sdm845.dtsi. So fix that
to align with DT nodes in sdm845.dtsi.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

Nokia RX-51: Remove CONFIG_PREBOOT from defconfig

CONFIG_PREBOOT just cause putting "preboot=CONFIG_PREBOOT" into env list.
Value CONFIG_PREBOOT="run preboot" in defconfig is just nonsense and does
not do anything useful (it is infinite recursion). Config file for this
board already contains default preboot= env variable with correct value,
which has higher priority than CONFIG_PREBOOT and this is reason why
nonsense CONFIG_PREBOOT is ignored.

Remove nonsense and unused CONFIG_PREBOOT from nokia_rx51_defconfig file.

Signed-off-by: Pali Rohár <pali@kernel.org>

board: ti: am335x: Use correct dtbs for SanCloud boards

We have different dtbs for the Lite and Extended WiFi variants of the
SanCloud BBE.

Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

board: ti: am335x: Enable spi0 bus on SanCloud BBE Lite

The SanCloud BBE Lite has a Micron Authenta flash device connected to
the spi0 bus.

Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

cmd: ti: ddr3: correct minor spelling mistake in Ti DDR3

Just a spelling mistake.

Signed-off-by: Ramin Zaghi <rzaghi@visualSilicon.com>

imx8mm: synchronise device tree with linux

Synchronise device tree with linux v5.19-rc5.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

board: toradex: apalis-imx8: fix file names in maintainers

Fix device tree file names in MAINTAINERS file.

Fixes: 3d6036650059 ("board: toradex: add apalis imx8qm 4gb wb it v1.0b module support")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

imx8mq: synchronise device tree with linux

Synchronise device tree with linux v5.19-rc5.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

verdin-imx8mp: synchronise device tree with linux

Synchronise device tree with linux v5.19-rc5.

Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mp-verdin-wifi-dev.dtb rather than the previous imx8mp-verdin.dtb).

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

imx8mp-rsb3720-a1: fix pwms property warnings

Fix the following build-time pwms property warnings:

w+arch/arm/dts/imx8mp-rsb3720-a1.dtb: Warning (pwms_property):
/lvds_backlight@0:pwms: property size (12) too small for cell size 3
w+arch/arm/dts/imx8mp-rsb3720-a1.dtb: Warning (pwms_property):
/lvds_backlight@1:pwms: property size (12) too small for cell size 3

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

imx8mp: synchronise device tree with linux

Synchronise device tree with linux v5.19-rc5.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

imx8mn: synchronise device tree with linux

Synchronise device tree with linux v5.19-rc5.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

imx8mm-mx8menlo/verdin-imx8mm: synchronise device tree with linux

Synchronise device tree with linux v5.19-rc5.

Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mm-verdin-wifi-dev.dtb rather than the previous imx8mm-verdin.dtb).

Please further note that the PMIC node name got changed from a pmic
label to pmic@25 which required adjustment in resp. board SPL file
board/toradex/verdin-imx8mm/spl.c.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

imx8mm-kontron-n801x-s-lvds: fix pwms property warnings

Fix the following build-time pwms property warnings:

w+arch/arm/dts/imx8mm-kontron-n801x-s-lvds.dtb: Warning (pwms_property):
/backlight:pwms: property size (12) too small for cell size 3

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

imx8mm-venice-gw700x: prepare to synchronise device trees with linux

As a preparatory step remove the pinctrl_pmic reference which does not
exist in the Linux upistream device tree.

This avoids the following error once synchronised:

+Error: arch/arm/dts/imx8mm-venice-gw700x-u-boot.dtsi:26.1-14 Label or
path pinctrl_pmic not found

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

colibri_vf: synchronise device tree with linux

Synchronise device tree with linux v5.19-rc5.

Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Colibri Evaluation (carrier) board V3 (e.g.
vf610-colibri-eval-v3.dtb rather than the previous vf610-colibri.dtb).

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

vf500/vf610: synchronise device trees with linux

Synchronise device trees with linux v5.19-rc5.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

ARM: DTS: bk4r1/pcm052: prepare to synchronise device trees with linux

As a preparatory step rename the included SoC dtsi from vf.dtsi to
vf610.dtsi as this is how it is named in Linux upstream.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

colibri-imx7d/-emmc: synchronise device tree with linux

Synchronise device tree with linux-next next-20220708.

Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device trees we are now using the
regular ones for the Colibri Evaluation (carrier) board V3 (e.g.
imx7d-colibri-eval-v3.dtb rather than the previous
imx7-colibri-rawnand.dtb and imx7d-colibri-emmc-eval-v3.dtb rather than
the previous imx7-colibri-emmc.dtb).

Please further note that the PMIC node name got changed from rn5t567@33
to pmic@33 which required adjustment in resp. board file
board/toradex/colibri_imx7/colibri_imx7.c.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

imx7s/d: synchronise device trees with linux

Synchronise device tree with linux-next next-20220708.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>